V-8 swap parts
Posted: Fri Jun 07, 2013 6:04 pm
No from me but thought some of you might really be interested on what he has for sale on TRS.
Dave
FS: V8 swapped 96 Ranger Partout - IN
so here's what's happening.. everything non stock related is for sale. if i dont have a factory piece to replace it with it is not forsale. if you want to purchase something of that nature then i will be interested in trading + cash from your end for a piece to make my truck a complete stock vehicle so that i can sell as a whole. if someone is willing to give me the money that i've got in the truck, and pick the truck up.. ill sell as a whole. other than that, it's getting taken apart and the money is being used for a down payment on a new mustang GT..
Trickflow TW170 61cc cylinder heads. these were just recently purchased and have only been on the truck for maybe the 100-200 miles it's got on it. Need $1000 for them
Trickflow stage 2 cam $125
Sorpion 1.6R roller rockers - $120
Trickflow 6.7" Push rods needed for TF heads - $50
Trickflow R upper and lower intake - 100-200 miles - $500
Trickflow R nitrous plate that goes between upper and lower intake - was new as well - $200
Ford racing valve covers - $120
Kaufman long tube headers for ibeam suspension trucks, newly ceramic coated (also includes ford racing dipstick that fits) - $400 or $430 with stage 8 locking bolt kit
newly built custom exhaust for use with extended cab long tube v8 rangers, 2 brand new dynomax mufflers built for side exit and use with factory rear exhaust hanger and 2 stainless tips, use with longtubes and it's a direct bolt on. $400
modded steering shaft setup for use with kaufman headers $150
30# injectors flow matched and without 1% flow. $160
Aeromotive aluminum fuel rails -8, aeromotive fpr, -8 feed and -6 return all fittings needed to plumb from factory sending unit to the rails and regulator. $500
255 pump $80
explorer front accessory drive with new water pump and all bearing'd pulleys are new. comes with short no ac belt and reg ac belt, also included -6 fitting in pump and lines to look to steering box, also includes upper and lower rad hoses $240
Motorcraft distributor with msd cap/rotor and ford racing 9mm wires and msd coil $120
Mustang mounts $30
75mm throttle body with custom throttle cable mount $100
Intake tube with slot maf flange welded on, filter, elbow, and ford slot maf $100
Centerforce clutch, flywheel, all hydraulics to convert to t5 $300
New starter from 95 mustang $100
Rebuilt T5 from a fox w/bellhousing and shifter fork and new throw out bearing $600
pro 5.0 shifter $100
Raised trans xmember $50
pedals with aftermarket billet covers $80
cowl hood $200 (requires factory white hood in good condition to put back on my truck)
clear front lights and corners (requires factory lights as trade) $100
Undercover bed cover $500
efans $50 comes with controller
traction bars (caltrac style) $140 includes front urethane bushings needed to install these
wet nitrous zex kit 125 shot jetted comes with controller, bottle, lines, and blow down tube $400
dual core 4.0 radiator - $80
ibeam cobra brake hubs and brackets for cobra conversion $300
A9L fox computer $100
Fox mustang harness already modified to plug directly into a 96-97 truck. includes trans harness as well $200
advance adapter oil filter relocation kit $50
Dave
FS: V8 swapped 96 Ranger Partout - IN
so here's what's happening.. everything non stock related is for sale. if i dont have a factory piece to replace it with it is not forsale. if you want to purchase something of that nature then i will be interested in trading + cash from your end for a piece to make my truck a complete stock vehicle so that i can sell as a whole. if someone is willing to give me the money that i've got in the truck, and pick the truck up.. ill sell as a whole. other than that, it's getting taken apart and the money is being used for a down payment on a new mustang GT..
Trickflow TW170 61cc cylinder heads. these were just recently purchased and have only been on the truck for maybe the 100-200 miles it's got on it. Need $1000 for them
Trickflow stage 2 cam $125
Sorpion 1.6R roller rockers - $120
Trickflow 6.7" Push rods needed for TF heads - $50
Trickflow R upper and lower intake - 100-200 miles - $500
Trickflow R nitrous plate that goes between upper and lower intake - was new as well - $200
Ford racing valve covers - $120
Kaufman long tube headers for ibeam suspension trucks, newly ceramic coated (also includes ford racing dipstick that fits) - $400 or $430 with stage 8 locking bolt kit
newly built custom exhaust for use with extended cab long tube v8 rangers, 2 brand new dynomax mufflers built for side exit and use with factory rear exhaust hanger and 2 stainless tips, use with longtubes and it's a direct bolt on. $400
modded steering shaft setup for use with kaufman headers $150
30# injectors flow matched and without 1% flow. $160
Aeromotive aluminum fuel rails -8, aeromotive fpr, -8 feed and -6 return all fittings needed to plumb from factory sending unit to the rails and regulator. $500
255 pump $80
explorer front accessory drive with new water pump and all bearing'd pulleys are new. comes with short no ac belt and reg ac belt, also included -6 fitting in pump and lines to look to steering box, also includes upper and lower rad hoses $240
Motorcraft distributor with msd cap/rotor and ford racing 9mm wires and msd coil $120
Mustang mounts $30
75mm throttle body with custom throttle cable mount $100
Intake tube with slot maf flange welded on, filter, elbow, and ford slot maf $100
Centerforce clutch, flywheel, all hydraulics to convert to t5 $300
New starter from 95 mustang $100
Rebuilt T5 from a fox w/bellhousing and shifter fork and new throw out bearing $600
pro 5.0 shifter $100
Raised trans xmember $50
pedals with aftermarket billet covers $80
cowl hood $200 (requires factory white hood in good condition to put back on my truck)
clear front lights and corners (requires factory lights as trade) $100
Undercover bed cover $500
efans $50 comes with controller
traction bars (caltrac style) $140 includes front urethane bushings needed to install these
wet nitrous zex kit 125 shot jetted comes with controller, bottle, lines, and blow down tube $400
dual core 4.0 radiator - $80
ibeam cobra brake hubs and brackets for cobra conversion $300
A9L fox computer $100
Fox mustang harness already modified to plug directly into a 96-97 truck. includes trans harness as well $200
advance adapter oil filter relocation kit $50
